Get a quote

EM-200-29 Hybrid Planetary Gearset Trainer + Add to wishlist

53137

The EM-200-29 Hybrid Planetary Gearset Trainer is designed to help instructors teach and students to understand the somewhat complex operation of a typical hybrid vehicle drivetrain. Based on a typical Toyota Prius hybrid vehicle, the trainer provides easy visualization of driveline component operation including:

  • ICE (Internal Combustion Engine)
  • MG1 (Motor/generator # 1)
  • MG2 (Motor/generator # 2)
  • Drive wheels

 

Educational Advantages

  • Clearly demonstrates the operation of ICE, MG1, MG2 and Drive wheels in all vehicle modes.
  • Students are required to be “part of the driveline operation” by turning hand cranks or holding devices which increases their engagement and involvement.
  • Trainer provides a significant educational tool that clearly demonstrates the complex operation of a hybrid drivetrain using a power split device.
  • Makes all major hybrid drivetrain components clearly visible which are normally not accessible in the vehicle.

 

Features

  • The EM-200-29 trainer is designed to have students manually rotate, hold or release each component using hand cranks.  An OPERATION DIAGRAM on the trainer gives instructions as to the status of each component during operational modes of:
    –  ELECTRIC DRIVE – Light acceleration & low speed (Stealth mode)
    –  ENGINE START –
    –  HYBRID DRIVE – Normal driving
    –  HYBRID DRIVE – High speed cruise or full throttle acceleration
    –  HYBRID DRIVE – High speed energy recirculation
    –  COASTING & REGENERATIVE BRAKING
    –  ELECTRIC DRIVE REVERSE
  • Clearly demonstrates the operation of ICE, MG1, MG2 and Drive wheels in all vehicle modes.
  • The OPERATION DIAGRAM identifies which component is held, driven and/or spins freely in each mode. Students either hold or turn hand cranks to demonstrate each mode. This allows full visualization of each mode for better understanding of system operation.   Each of the four components will react exactly as it does in the vehicle including changes in the direction of rotation of MG1. Diagnostic scenarios can also be created for example by showing what would happen if MG1 fails. In some modes, two students are required to operate all components on the trainer.
  • Clear representation of driveline components including ICE, MG1, MG2 and Drive wheels.
  • Hand cranks and drums that are used by students to either drive or hold components to  demonstrate each operational mode.

You must be connected to access this section. Please register or, if you already have an account, login.

You must be logged in to write a review about our products.

HYBRID PLANETARY GEARSET TRAINER



ConsuLab's EM-200-29 Hybrid Planetary Gearset Trainer is designed to help automotive instructors teach and students to understand the somewhat complex operation of a typical hybrid vehicle drivetrain

 
 

Testimonials

I got the half car out of the crate and working yesterday and today I had my Level 3 Electronic Climate Control diagnostics lab using it. This teaching aid is great! The workmanship and design is excellent and it is just perfect for the Level 3 curriculum, including the upcoming changes. We were fortunate that the IPro scan tool we received from the Uniselect donation communicates quite well with the Audi CAN bus system. The Audi also has the electronically controlled, clutchless compressor which is covered in our theory classes so it's a good reinforcement to be able to see it in action, manipulate it and communicate with it. I am very pleased with the quality and applicability of our ConsuLab products (including the engine/AC bench we got recently). They allow me to teach up to 8 students in great detail, whereas only one or two at a time can be involved in a full car. I am looking forward to the imminent arrival of our AC board. Thanks for your excellent insight of design and quality of manufacturing.

Prof. Thomas Brown, Centennial College

Partners

   
 
All Partners

Consulab

Consulab manufactures educational training materials adapted to meet the needs of technical and vocational schools in the fields of transportation technology electrical engineering.

Learn More

Contact

+1 (800) 567-0791 . 8pm - 5pm EST

4210 Jean-Marchand Street
Quebec City, QC . Canada, G2C 1Y6

Email info@consulab.com

More Information